The orthodontic lab wire bench: a kit list for removable appliance work

The orthodontic lab wire bench: a kit list for removable appliance work

Quick answer: A removable appliance wire bench needs four things: forming pliers (an Adams plier and a round nose plier at minimum, with a three-jaw for contouring), a hard wire cutter that is only ever used for wire, a controllable heat source such as a spirit lamp, and simple measuring tools. Buy the pliers and cutter first; add the rest as the work grows.

Chairside orthodontic kit gets most of the attention, but a great deal of orthodontic wire is formed on a laboratory bench: clasps, springs, bows and the other components of removable appliances. The bench that does this work is small, and almost every tool on it is used every day. This kit list is written for technicians and dental technology students setting up, or replacing, that bench.

Clinical dental students start from a different list: our guide to the dental student instrument kit covers their examination set, a wax carving kit and what to skip.

1. Forming pliers: the core of the bench

Adams pliers

The Adams pliers are the plier most associated with clasp-making. Ours are 13 cm with two smooth, rectangular beaks that end in sharp-edged grasping surfaces, designed for a secure hold on wire and crisp right-angle bends. If the bench has one specialist plier, it is usually this one.

Round nose pliers

Loops, coils and curved springs are formed around a round jaw. The round nose pliers are 127 mm with smooth, tapered conical jaws and a box joint; moving along the taper changes the loop size, so one plier covers a range of diameters.

Three-jaw pliers

The three-jaw wire contouring pliers press wire between one jaw and two opposing jaws, producing consistent angles and smooth curves without marring the surface. They are the contouring tool for bows and longer components where a round nose would leave a series of small kinks.

Many technicians add a bird beak (one round and one square beak) or a Tweed loop former later. Those patterns, and what each does that the others cannot, are compared in the wire-bending pliers guide.

For holding wire rather than forming it, the Howe pliers with curved jaws are 14 cm long with slender curved tips, and are intended for general dental laboratory tasks as well as arch-wire placement.

2. Cutting: one cutter, one job

The fastest way to ruin a forming plier is to cut with it, and the fastest way to ruin a fine cutter is to put hard wire through it. The bench needs a dedicated hard wire cutter, rated for the hard wire it will cut and kept for wire only. Softer ligature work belongs with a fine pin-and-ligature cutter instead; the difference between the three cutter types is set out in the orthodontic cutters guide.

3. Heat: a controllable flame

Lab benches use a small flame for jobs such as softening and shaping wax and annealing small components. The alcohol spirit lamp is made from polished stainless steel, runs on methylated spirits, has a wide, stable base and comes with a fitted snuffer cap that puts the flame out and stops the fuel evaporating between uses. It is a laboratory accessory rather than a medical device.

Treat any open flame on a bench with the care your workplace’s fire-safety procedures require: keep it clear of wax shavings and paper, cap it when it is not in use, and only refill it when it is out and cool.

4. Measuring and checking

Wire components are checked against the model as they are formed, but a bench also benefits from simple measuring tools for thickness and spacing. A spring wax caliper or a Boley gauge from the examination and lab ranges covers most needs, and both reprocess like any other stainless instrument.

5. A sensible buying order

  1. Adams pliers and round nose pliers: the two you cannot work without.
  2. A hard wire cutter, kept strictly for wire.
  3. Three-jaw pliers for contouring longer components.
  4. A spirit lamp, if the bench does not already have a heat source.
  5. Specialist patterns (bird beak, Tweed) and a second round nose as volume grows.

The Adams, round nose and three-jaw pliers above are in our orthodontic and wire pliers collection.

6. Keeping the bench tools true

Forming pliers stay accurate for as long as their jaws stay aligned and unmarked. Close each plier on paper against the light when it is new and every so often afterwards: even contact along the jaws means it is fine; daylight at the tips or sideways play means the joint has worn. Do not use forming pliers on wire heavier than they are designed for, and store them so the tips cannot knock together. If your pliers also go chairside, reprocess them according to your practice’s decontamination policy and the instructions supplied with the instrument.

UK delivery is free on orders from £30, and we aim to dispatch orders placed before 2pm UK time, Monday to Friday, the same working day. Returns are accepted within 30 days on sealed items.

Frequently asked questions

What pliers does a dental technician need for removable appliances?

At minimum, Adams pliers for clasp work and right-angle bends, and round nose pliers for loops and springs. Three-jaw pliers are the usual third plier for smooth contours on longer components.

Can I cut orthodontic wire with forming pliers?

No. Cutting with forming pliers damages the jaws, and marked jaws then score the wire. Use a dedicated hard wire cutter for hard wire and keep it for wire only.

What fuel does the spirit lamp use?

The spirit lamp is designed for methylated spirits. It has a fitted snuffer cap to put out the flame and reduce fuel evaporation between uses.

How do I check whether a plier is still accurate?

Close it gently on a piece of paper held up to the light. The jaws should meet evenly along their length with no gap at the tips and no sideways play. A gap or wobble means the joint has worn.

Related reading