Quick answer: Width and angle are the two variables. Narrow blades (1–2 mm) are the finest; 3 mm is the common middle; 5 mm is the broadest. Straight blades suit direct access, while down-angled and contra-angled necks change the approach where a straight shaft would be awkward. A practical first selection is one narrow, one 3 mm and one 5 mm straight, with an angled 3 mm added for access; a colour-coded set covers the range in one purchase.
Luxators are among the most personal instruments on an extraction tray. They are sold singly, in several widths and angles, and the choice of which to keep within reach is shaped by training and preference. That is a clinical decision we do not try to make for you. What we can do is explain what each variable changes, so that the instruments you buy match the way you were taught to work.
1. What a luxator is designed to do
A luxator has a fine, sharp, tapered blade designed to enter the periodontal space; product descriptions in our range describe them for severing the periodontal ligament ahead of extraction. That fine edge is what separates a luxator from a conventional elevator, which is built more robustly for leverage. How the two differ in geometry and handle design is covered in our luxating vs conventional elevators guide.
For comparison, our Coupland and Cryer pattern elevators are conventional elevators: a five-piece set with three straight Couplands in 2, 3 and 4 mm widths and a left and right pair of triangular Cryers.
2. Width: 1, 2, 3 or 5 mm
Blade width is the first number on every listing.
- 1 mm: the finest. Our 1 mm straight luxator has a fine, tapering blade and a colour-coded handle.
- 2 mm: the green-handled 2 mm straight luxator has a tapered blade and a green handle for quick identification.
- 3 mm: the most common middle width. The straight 3 mm luxator has a textured grey handle for grip.
- 5 mm: the broadest in our range. The straight 5 mm luxator has a yellow composite handle.
Narrower blades are finer and reach into tighter spaces; broader blades present more edge. Most trays carry more than one width for exactly that reason.
3. Angle: straight, down-angled or contra-angled
The second variable is the shape of the neck.
- Straight: blade in line with the handle. The simplest to control where access is direct.
- Down-angled: the blade is angled relative to the handle. We list 3 mm and 5 mm down-angled luxators, and their descriptions mention the angle as an aid to access and leverage.
- Contra-angled: the neck is bent so the blade sits back in line with the handle’s axis. Our contra-angled 3 mm luxator describes the design as improving visibility and leverage in confined areas.
Angled instruments change the approach, not the job. Whether a straight or angled neck suits a particular situation is part of clinical judgement and training.
4. Colour coding
When several luxators sit side by side, the blades look alike; the handles should not. Coloured handles let you identify width at a glance, which saves time at the chair and when sorting after reprocessing. If you buy singles, consider keeping one colour per width across the practice so that everyone reads the tray the same way.
5. Singles or a set?
Singles let you build exactly the selection you want and replace one worn instrument without buying the rest. A set covers the range in one purchase and keeps handles consistent. The seven-piece luxating elevator set contains seven differently configured luxators with colour-coded handles, titanium nitride coated working tips for surface hardness and wear resistance, and micro-serrations on the tips designed to reduce slippage. For a new surgery or a first personal selection, a set is usually the simpler route; for topping up, singles make sense.
Lever-type elevators come as a set too. The 8-piece elevator and lever set has straight, angled and curved tips, and each instrument is packed individually, with no case or pouch.
6. Protecting the edge
A luxator is only as good as its edge, and a fine edge is easily damaged by knocks against other instruments. Store and reprocess luxators so that the blades are protected, for example in a cassette with rails or a dedicated slot, and inspect the tip before use: a rolled, chipped or bent tip should be taken out of service. Several of our single luxators list compatibility with more than one sterilisation method; follow the listing, the instructions supplied with the instrument and your practice’s decontamination policy. Coated tips must not be sharpened through the coating; edge maintenance and retirement are covered in the sharpening guide.
UK delivery is free on orders from £30, and we aim to dispatch orders placed before 2pm UK time, Monday to Friday, the same working day. Returns are accepted within 30 days on sealed items.
Frequently asked questions
What widths do luxators come in?
Our range includes straight luxators with 1 mm, 2 mm, 3 mm and 5 mm blades, plus down-angled 3 mm and 5 mm and a contra-angled 3 mm. Narrower blades are finer; broader blades present more edge.
What is the difference between a down-angled and a contra-angled luxator?
A down-angled luxator has the blade angled relative to the handle. A contra-angled luxator has a bent neck that brings the blade back towards the handle’s axis, which is described as improving visibility and leverage in confined areas.
Should I buy luxators singly or as a set?
A set covers a range of configurations in one purchase with consistent, colour-coded handles, which suits a new surgery or a first selection. Singles suit topping up or replacing one worn instrument.
How do I protect a luxator’s edge?
Keep the blade away from other instruments during storage and reprocessing, for example in a cassette slot, and inspect the tip before use. Take a rolled, chipped or bent tip out of service, and never sharpen through a coating.
Related reading
- Luxating vs conventional elevators — how blade geometry and handle design decide which belongs on your tray.
- Sharpening dental instruments — keeping luxator edges true, and when to retire them.